Mounts & Acessories

Made of high strength aluminum with Mil-Spec Type III hard coat anodized finishFeatures a non-glare coating to reduce reflectionsMakes the A3 rifle compatible with the Clawgear AUG HandguardFeatures a 30 slot picatinny rail (NATO STANAG 4694)Anti-rotational QD attachment point at the front

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe nine slot Picatinny rail allows the user to upgrade his AK rifle with various aiming devices or accessories.Adjustment ScrewsAdjust the angle of the mount to align it with the point of bullet impact.Shaped ContourThe design fits to the curve on the receiver cover and even allows to dissable the rifle without dismounting the AK RSM.Emergency SightEven with an optical device mounted the sight can be used as a backup.Compatibility: AK-47, AKM, RPK, AK-74 and all variants with the original Mauser-type adjustable rear sight. Not compatible with SKS rifles.Installation: Dismount the existing rear sight and leaf spring. Put the AK RSM into the guidance on the rear sight base and align both holes. Punch the included roll pin into the bore so it is flush with both sides. Insert the big set screw on top into the middle thread on the rail and tighten it until the emergency sight aims to the point of impact. Finally insert both small set screws into the forward threads and tighten them stoutly. Warning: Torque for setscrew max. 3 NM

Clawgear‘s modular mounting system products are designed to increase weapon performance and handling. Due to it‘s construction in 6082 Aluminum, this rugged and high quality item will serve you in any combat situation.NATO STANAG 4694 RAILThe 13 slot Picatinny Rail allows the user to upgrade his 55X rifle with various aiming devices or accessories.LIGHTWEIGHT CONSTRUCTIONAlthough this mount base has been designed in a lightweight way, its mechanical strength is not being affected.ADJUSTMENT SCREWIt clamps the mount for a solid fit between both attachment points on the receiver and is secured by a clamp screw on the left side.DOVETAIL SLOTThe front attachment point is the dovetail on the receiver which is normally used to fix the brass catcher.AIMING BOREMakes the use of the original diopter sights possible.CompatibilitySIG550, SIG551, SIG552, SIG553, PE90 and all variants of the ri_x001E_ e with standard adjustable diopter sights.InstallationMake sure your weapon is unloaded and safe. Screw the included adjustment screw fully into the mount base. Put the rail on the upper receiver and slide it forward so the dovetail on the receiver connects smoothly to the front of the rail. Then use a 8mm wrench to unscrew the adjustment screw until it moves inside the hole of the rear sight base. Tighten it up for a solid fit. Use the clamp screw on the left side of the mount base to secure its position.

Clawgear‘s modular mounting system products are designed to increase weapon performance and accuracy. Due to its glass fibre reinforced polymer construction, this rugged and high quality item will serve you in any combat situation. The Modular Scope Mount protects the original optics of AUG rifles and provides mounting possibilites for various Picatinny based accessories.NATO STANAG 4694 RailThe integrated 16 slot Picatinny Rail allows the user to upgrade his AUG rifle with various aiming devices or accessories.Lightweight ConstructionAlthough this mount base has been designed in a lightweight way, its mechanical strength is enhanced by the use of glass fiber reinforced polymer.Mounting PossibilitesAdditional side rails (sold seperately) can be attached to both sides of the AUG MSM to provide additional mounting spots for further equipment.Reduced Infrared SignatureThis accessory part features reduced infrared singature.Flip-Up CoversTwo flip-up covers (included) protect the lenses of the scope from rain, dust, debris and mud.InstallationMake sure your weapon is unloaded and safe. Take the left half-shell (the one without top rail) and place it on the scope by pushing it over the diagonal fixing screw of the scope. Then push the right half-shell into the corresponding slots on the left part until it clicks in. Make sure that all engagement hooks are snapped in. Place each hexagon nut in the clearance of the right shell and tighten the corresponding screw from the left shell side. Mount the included flip-up covers to protect the original scope glass.CompatibilitySteyr AUG A1/A2, AUG P, AUG Z, AUG LMG variants, AUG SA variants, F88 Austeyr. Applies to all variants with 1,5x standard Steyr scope.

Clawgear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe 4 slot Picatinny rail allows the user to upgrade his Modular Scope Mount equipped AUG rifle with additional accessories.SurfaceHigh alloy aluminium with anodized coating (MIL-8625-F type III, class II) for heavy use.This rails fits the AUG Modular Scope Mount (Art.Nr. 20114)

Clawgear‘s modular mounting system products are designed to increase weapon performance and handling. Due to it‘s construction in 6082 Aluminum, this rugged and high quality item will serve you in any combat situation.NATO STANAG 4694 RAILThe 13 slot Picatinny Rail allows the user to upgrade his 55X rifle with various aiming devices or accessories.LIGHTWEIGHT CONSTRUCTIONAlthough this mount base has been designed in a lightweight way, its mechanical strength is not being affected.ADJUSTMENT SCREWIt clamps the mount for a solid fit between both attachment points on the receiver and is secured by a clamp screw on the left side.DOVETAIL SLOTThe front attachment point is the dovetail on the receiver which is normally used to fix the brass catcher.CompatibilitySIG550, SIG551, SIG552, SIG553, PE90 and all variants of the rifle with standard adjustable diopter sights.InstallationMake sure your weapon is unloaded and safe. Screw the included adjustment screw fully into the mount base. Put the rail on the upper receiver and slide it forward so the dovetail on the receiver connects smoothly to the front of the rail. Then use a 8mm wrench to unscrew the adjustment screw until it moves inside the hole of the rear sight base. Tighten it up for a solid fit. Use the clamp screw on the left side of the mount base to secure its position.